background image

2         

COPYRIGHT & TRADEMARKS 

Specifications are subject to change without notice. 

  is a 

registered trademark of Rosewill Inc. Other brands and product names are trademarks 

or registered trademarks of their respective holders. 

No part of the specifications may be reproduced in any form or by any means or used to 

make any derivative such as translation, transformation, or adaptation without 

permission from Rosewill Inc. Copyright © 2010 Rosewill Inc. All rights reserved. 

http://www.rosewill.com

 

 

FCC STATEMENT

 

 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that 

to         
        which the receiver is connected.   

 

Consult the dealer or an experienced radio/ TV technician for help. 

This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 

1) 

This device may not cause harmful interference. 

2) 

This device must accept any interference received, including 

interference that may cause undesired operation. 

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV 
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS 
EQUIPMENT. S

UCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO 

OPERATE THE EQUIPMENT. 

Summary of Contents for RFS-108P












Reviews: