background image

3         

 
CE Mark Warning 

 

This is a class A product. In a domestic environment, this product may cause radio 
interference, in which case the user may be required to take adequate measures. 

Safety Warning 

 

Place connecting cables carefully so that no one will step on them or 
stumble over them. 

 

Always disconnect all cables from this device before servicing or 
disassembling. 

 

Use ONLY an appropriate power adaptor or cord for your device. 

 

Connect the power adaptor or cord to the right supply voltage (for example, 
110V AC in North America or 230V AC in Europe). 

 

Do not allow anything to rest on the power adaptor or cord and do not place 
the product where anyone can walk on the power adaptor or cord. 

 

Do not use the device if the power adaptor or cord is damaged as it might 
cause electrocution.   

 

If the power adaptor or cord is damaged, remove it from the power outlet. 

 

Do not attempt to repair the power adaptor or cord. Contact your local 
vendor to order a new one. 

 

Do not use the device outside, and make sure all the connections are 
indoors.   

 

Do not obstruct the device ventilation slots, as insufficient airflow may harm 
your device. 

 

Do not use this product near water, eg, in wet basement, or near a 
swimming pool. 

 

Do not expose your device to dampness, dust or corrosive liquids. 

 

Do not install, use, or service this device during a thunderstorm. There is a 
remote risk of electric shock from lightning. 

 

Connect ONLY suitable accessories to the device. 

 

Do not open the device or unit. Opening or removing covers can expose 
you to dangerous high voltage points or other risks. ONLY qualified service 
personnel should service or disassemble this device. Please contact your 
vendor for further information. 

 

Make sure to connect the cables to the correct ports. 

 

If you wall mount your device, make sure that no electrical lines, gas or 
water pipes will be damaged. 

 

Your product is marked with this symbol, which is 
known as the WEEE mark. WEEE stands for Waste 
Electronics and Electrical Equipment. It means that used 
electrical and electronic products should not be mixed 
with general waste. Used electrical and electronic 
equipment should be treated separately.   

 

 

Summary of Contents for RFS-108P












Reviews: