manualshive.com logo in svg

Rosemount Series 8700, Reference Manual

Share
Download
Rosemount Series 8700 Reference Manual Download Page 29

Reference Manual 

00809-0100-4727, Rev EA
October 2010

Rosemount 8700 Series

www.rosemount.com

Section  3

Operation and Maintenance

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1

Grounding  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1

Material Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-3

Magnetic Flowmeter Sizing  . . . . . . . . . . . . . . . . . . . . . . . . page 3-4

This section covers basic operation, software functionality, and basic 
configuration procedures for the Magnetic Sensor. For more information about 
the technology and the function blocks used in the sensor, refer to 
Appendix A: Reference Data and Appendix C: Field-Removable Electrodes.

CALIBRATION

Rosemount sensor are wet calibrated at the factory. They do not need further 
calibration during installation.

GROUNDING

Process grounding the sensor is one of the most important details of sensor 
installation. Proper process grounding ensures that the transmitter amplifier is 
referenced to the process. This creates the lowest noise environment for the 
transmitter to make a stable reading. Use Table 3-1 to determine which 
grounding option to follow for proper installation. 

NOTE

Consult factory for installations requiring cathodic protection or situations 
where there are high currents or high potential in the process. 

The sensor case should always be earth grounded in accordance with 
national and local electrical codes. Failure to do so may impair the protection 
provided by the equipment. The most effective grounding method is direct 
connection from the sensor to earth ground with minimal impedance.

The Internal Ground Connection (Protective Ground Connection), located 
inside the junction box, is the Internal Ground Connection screw. This screw 
is identified by the ground symbol:

Table 3-1.  Grounding Installation

Grounding Options

Type of Pipe

No Grounding Options

Grounding Rings

Grounding Electrodes

Lining Protectors

Conductive Unlined Pipe

See Figure 3-1

Not Required

Not Required

See Figure 3-2

Conductive Lined Pipe

Insufficient Grounding

See Figure 3-2

See Figure 3-1

See Figure 3-2

Non-Conductive Pipe

Insufficient Grounding

See Figure 3-3

See Figure 3-4

See Figure 3-3

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for Series 8700



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands