Rosemount 333 HART Tri-Loop Product Manual Download Page 5 | Manualshive

Page: 5 / 48

background image

Table of Contents

iii

SECTION 1
Introduction

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

SECTION 2
Installation

System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Unpacking The HART Tri-loop . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Initial Inspection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
Model 3095 MV (or HART Multivariable Device)  . . . . . . . .  2-3
Alarms   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-3
Failure Mode Alarm vs. Saturation Output Values  . . . . . . .  2-3

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Mechanical Considerations  . . . . . . . . . . . . . . . . . . . . . . . . . .  2-4
Electrical Considerations   . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-5
Power Supply  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-5

Installation Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

1. Review Installation Considerations  . . . . . . . . . . . . . . . . .  2-6
2.Mount Tri-Loop on DIN Rail  . . . . . . . . . . . . . . . . . . . . . . .  2-6
3. Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-6
Configure the Model 3095 MV For Tri-loop Operation  . . . .  2-8
Select Process Variables   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2-8
Record Model 3095 MV Units  . . . . . . . . . . . . . . . . . . . . . . . .  2-9
Set the Model 3095 MV to Burst Mode   . . . . . . . . . . . . . . .  2-10

SECTION 3
Commissioning

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Install The Tri-loop Configurator Software . . . . . . . . . . . . . . . . 3-1

Minimum Equipment and Software . . . . . . . . . . . . . . . . . . . 3-2
Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Configure the Tri-loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Help Files  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-3
Connect the PC to the Tri-Loop   . . . . . . . . . . . . . . . . . . . . . .  3-3
Configuration Procedure  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3-4

Menu Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

«
...
3
4
5
6
7
...
»

Summary of Contents for 333 HART Tri-Loop

















































Reviews:

No comments

Related manuals for 333 HART Tri-Loop

Brand: Saftronics Pages: 62

Brand: CEL-MAR Pages: 16

Brand: ZIPPER MASCHINEN Pages: 100

Brand: IAdea Pages: 14

Brand: Xantech Pages: 2

Mega 100 Classic

Brand: Ellumiglow Pages: 4

Brand: Black Box Pages: 20

Y/C to NTSC Conversion PCN-40

Brand: Link Pages: 2

Brand: Wirez Pages: 16

EQUINOX EQX2 4002-HT

Brand: Salicru Pages: 108

Brand: Audio Technica Pages: 11

Brand: Aegis Pages: 20

1080PXX-LED Button

Brand: EYEZONE Pages: 8

Brand: Audioplex Pages: 2

Symo Hybrid 3.0-3-S

Brand: Fronius Pages: 140

Brand: Zling Pages: 12

Brand: SMA Pages: 272

Brand: Camos Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands