Rosemount 333 HART Tri-Loop Product Manual Download Page 45

Page: 45 / 48

B-11

Appendix B

Message

Description

Mark as read only
variable on hotkey
menu?

Asks whether the user should be allowed to edit the variable from
the hotkey menu if the item being added to the hotkey menu is a
variable.

No device configuration
in configuration memory

There is no configuration saved in memory available to re-
configure off-line or transfer to a device.

No Device Found

Poll of address zero fails to find a device, or poll of all addresses
fails to find a device if auto-poll is enabled.

No hotkey menu available
for this device.

There is no menu named “hotkey” defined in the device
description for this device.

No offline devices
available.

There are no device descriptions available to be used to configure
a device offline.

No simulation devices
available.

There are no device descriptions available to simulate a device.

No UPLOAD_VARIABLES
in ddl for this device

There is no menu named “upload_variables” defined in the device
description for this device. This menu is required for offline
configuration.

No Valid Items

The selected menu or edit display contains no valid items.

OFF KEY DISABLED

Appears when the user attempts to turn the HC off before sending
modified data or before completing a method.

Online device
disconnected with
unsent data. RETRY or
OK to lose data.

There is unsent data for a previously connected device. Press
RETRY to send data, or press OK to disconnect and lose unsent
data.

Out of memory for hotkey
configuration. Delete
unnecessary items.

There is no more memory available to store additional hotkey
items. Unnecessary items should be deleted to make space
available.

Overwrite existing
configuration memory

Requests permission to overwrite existing configuration either by
a device-to-memory transfer or by an offline configuration. User
answers using the softkeys.

Press OK...

Press the OK softkey. This message usually appears after an error
message from the application or as a result of HART
communications.

Restore device value?

The edited value that was sent to a device was not properly
implemented. Restoring the device value returns the variable to its
original value.

Save data from device to
configuration memory

Prompts user to press SAVE softkey to initiate a device-to-
memory transfer.

Saving data to
configuration memory.

Data is being transferred from a device to configuration memory.

Sending data to device.

Data is being transferred from configuration memory to a device.

There are write only
variables which have not
been edited. Please edit
them.

There are write-only variables which have not been set by the
user. These variables should be set or invalid values may be sent
to the device.

Summary of Contents for 333 HART Tri-Loop

















































Search results

Summary of Contents for 333 HART Tri-Loop

Reviews:

Related manuals for 333 HART Tri-Loop

Brands by name

Popular brands

Rosemount 333 HART Tri-Loop, Product Manual

Search results

Summary of Contents for 333 HART Tri-Loop

Reviews:

Related manuals for 333 HART Tri-Loop

Brands by name

Popular brands