RONDELL RDE-1750, Manual Instruction

Page: 13 / 32

13
– Do not leave children unattended to avoid them using the
unit as a toy.
– Do not use the unit if its body, the power cord or the power
plug is damaged.
– If any malfunction is detected, and after it was dropped,
unplug the unit and contact any authorized service center.
– If the power cord is damaged, it must be replaced by the
manufacturer, service department or similar qualified per-
sonnel to avoid potential injuries.
– To avoid potential injury, do not attempt to repair the
unit by yourself. Do not disassemble the dehydrator by
yourself, if there is any malfunction or after the unit was
dropped, unplug it and contact any authorized service
center at the contact addresses in the warranty card and
on the website www.rondell.ru.
– Transport the unit in the original packaging only.
– Keep the unit in a dry cool place out of reach of children
and people with disabilities.
ATTENTION! Do not switch the unit on for more than
24 hours in one go. After 24 hours, unplug it and let it cool
down for at least 2 hours before plugging it back in.
– Do not use the unit as a heater!
– Misuse and mishandling may result in unit malfunction
and injury to the user.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS
AND WORK SPACES IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low temperature
keep it for at least three hours at room temperature be-
fore switching on.
– Take the dehydrator out of the package and remove the
packaging materials.
– Check the unit for damages, do not use it if it is damaged.
– Make sure that operating voltage of the dehydrator corre-
sponds to the voltage of your mains.
– Before using the dehydrator for the first time, wash all
removable parts (3, 4, 7) with warm water and neutral
detergent and dry them.
– Clean the inside of the dehydrator chamber with a slightly
damp cloth and wipe it dry. Use detergent if necessary.
– Unwind the power cord completely before plugging it in.
– After cleaning, run the dehydrator for 30 minutes without
placing any food products in it.
Note: during the first operation some foreign smell from the
heating element is possible, this is normal.
USING THE UNIT
– Before drying wash the food products, dry them and cut
into small pieces.
– Put the food products on the dehydration grids (3) pro-
viding space for hot air circulation between the pieces.
Remember that hot air should circulate freely. The grids
(3) should be oriented with the mesh upwards, since
the places of welding of the grid with the base (rim) may
prevent free movement of the grids in the guides of the
chamber.
– Place the plastic tray (7) on the bottom of the chamber,
and the grids (3) into the guides of the dehydrator cham-
ber and close the door (5).
– Plug the unit in, you will hear a sound signal, while
the «Start/Stop» «
START
STOP
» buttons (8), «Time/Temperature»
«
TIME
TEMP
» (9), «Decrease» « » (11), «Increase» « » (12)
will light up and the display (10) will show the «8888»
« » symbols. In three seconds, all buttons will go
out, and the «Time/Temperature» «
TIME
TEMP
» button (9) will
start flashing, the display will show the «0000» « »
symbols. The dehydrator will go into standby mode.
– Press the «
TIME
TEMP
» button (9), the LED display will show and
flash the temperature value, the default is « ». By
consequently pressing the buttons «Decrease» « » (11)
or «Increase» « » (12) buttons, set the drying tempera-
ture from «35 °C» to «75 °C». Each press of the «Decrease»
« » (11) or «Increase» « » (12) buttons will change the
temperature value by 5 °C. To quickly set the desired
value, press and hold the corresponding button.
Note: If no other button is pressed within 5 seconds, the unit
will accept the set temperature, and the «Start/Stop» «
START
STOP
»
button (8) will start flashing.
– Press the «Time/Temperature» «
TIME
TEMP
» button (9) again,
while the display (10) will show and flash the value of
the drying time, the default is «10:00» « », and the
«Time/Temperature» «
TIME
TEMP
» button (109) will be constantly
lit up. By consequently pressing the «Decrease» « » (11)
or «Increase» « » (12) buttons, set the drying time from
30 minutes to 24 hours in increments of 30 minutes. To
quickly set the desired value, press and hold the corre-
sponding button.
– Note: If no other button is pressed within 5 seconds, the
unit will accept the set time, and the «Start/Stop» «
START
STOP
»
button (8) will start flashing.
ATTENTION! If the unit is not started within 60 seconds
using the «Start/Stop» «
START
STOP
» button (8), it will automatically
return to standby mode, while the set temperature and dry-
ing time will return to the default values.