background image

 
 

Rev 20.11.2019 

V1.07 - Page 12 

Subject to modifications! 

romutec Steuer.-und Regelsysteme GmbH   Jochsberger Straße 39    D-91592 Buch am Wald 

www.romutec.de 

Subject to technical changes 

 

 
 

 
 

Overview terminal assignment: 

 
 
 

romod 8 DO eco 

 

 

 

 

 

 

 

 

 

 

 

 

DOs with ground referenced 
semiconductor o24 V DC! 

 

G

ND

 

2

4

AC/

DC

 

+2

4

V

 DC

  

fo

D

O

s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DO No. 1-8 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminal: 

 

 

 

 

 

11 

 

12 

 

13 

 

14 

 

15 

 

16 

 

17 

 

18 

 

+24VDC for DOs 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminal: 

 

 

10  19 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power supply 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminal: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
The two supply terminals (10 + 19) for the DOs are connected with each other internally. 
 
 
 

Bus connection 

Terminal No.

 

I-GND 

 

 

 

Net A (

–) aka /D 

 

 

 

Net B (+) aka D 

 

 

 

 
 
 
 

 

Summary of Contents for romod
















































Reviews: