background image

 

 

                  

 

 

 

15. Troubleshooting 

 

Problem: The Clip On Prism (or other accessory) will not fit on the front lens of the projector 
• Check that the ‘click-clack’ has not been removed.  This is a cylindrical piece that sits inside 
the lens (shown below).  Check that this is not still attached to the accessory that has 
previously been removed from the projector.  Reattach this part to fit an accessory onto the 
front lens in order to attach an accessory. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Problem: My Wheel Rotator has a cable with 2 pins – where does this connect? 
• Older Wheel Rotators are no longer compatible with this Projector.  Please purchase a 
Wireless Wheel Rotator (22614 or 22613) and compatible Effect Wheels 
 
Should you need to contact us about this product, please have the serial number to hand.

 

This can be located as indicated below: 

 

 

In the unlikely event of product failure, please contact us.  

 

 

Further copies of these instructions can be downloaded at www.rompa.com 

We hope you find our instructions invaluable.  If you have any suggestions for improving 
them further your comments will be greatly received – please contact us at 

[email protected]

 

 

LED100 PROJECTOR 23008, May 2019 

Copyright ROMPA® Ltd 

Summary of Contents for 23008










Reviews: