background image

11 

| Automate

 Installation Instructions | DC Power Distribution Panel   

ROLLEASE ACMEDA

5 TROUBLESHOOTING

WIRE GAUGE DIMENSIONS

IMPORTANT!

WARNING: Distribution panel is connected to (120V/240V) mains power. Do not attempt to troubleshoot panel without first 
disconnecting all power and waiting a period of 5 minutes.
AVERTISSEMENT: le panneau de distribution est connecté au secteur (120V / 240V). Ne pas tenter dépanner le panneau 
sans d’abord couper l’alimentation et attendre un certain temps de 5 minutes.

PROBLEM

CAUSE

REMEDY

No Motors are responding

A/C power supply not plugged in

Check exterior LED

Check Panel to power connection and 

IEC connector and AC plug

Internal power switch turned off

Power is supplied to panel, but 

exterior LED is not lit. Open panel and 

switch internal power switch to ON 

position

A/C terminal block wiring is incorrect

CAUTION: 

Do NOT attempt to rewire 

mains power terminal block. Only to 

be performed by a suitably qualified 

installer

Individual Motor is not 

responding

Motor channel fuse has blown

Check individual LED’s

Replace fuse as necessary (refer to 

section 1.5)

Motor wiring is  incorrect

Refer to wiring diagram on page 6

Motor is in sleep mode

Refer to motor’s programming 

instructions in order to change motor 

sleep status

AMERICAN WIRE GAUGE DIMENSIONS

WIRE GAUGE

DIAMETER

CROSS-SECTIONAL AREA

24 AWG

0.51054 mm (0.0201 in)

0.205 mm

2

 (0.00032 in

2

)

22 AWG

0.64516 mm (0.0254 in)

0.326 mm

2

 (0.00051 in

2

)

20 AWG

0.8128 mm (0.032 in)

0.518 mm

2

 (0.00080 in

2

)

18 AWG

1.02362 mm (0.0403 in)

0.823 mm

2

 (0.00128 in

2

)

16 AWG

1.29032 mm (0.0508 in)

1.31 mm

2

 (0.00203 in

2

)

Summary of Contents for AUTOMATE MT03-0301-411005

















Reviews: