background image

10 

| Automate

 Installation Instructions | DC Power Distribution Panel   

ROLLEASE ACMEDA

3.6  Status LED Indication

IMPORTANT!

Status LEDs for each motor channel indicate the condition of the inline fuse. If the status LED is not lit up when 
power is supplied to the panel, then the inline fuse for that channel has blown.

Disconnect all power to the Panel and inspect the individual motor and supply cable to the motor in order to 
determine why the fault occurred.

Once the fault has been determined, make the appropriate repairs and replace the fuse with a 3.15A M205 
quick blow fuse.

In order to replace fuse, carefully pry the fuse out of the plastic cradle using a small tool (such as a small 
screwdriver or pen). To replace, gently press the new fuse into the cradle.

To test LED, apply power to the distribution panel, and observe whether the channel LED is glowing.

3.15A M205 fuse in 

plastic cradle

Green Fuse Status LED

TECHNICAL SPECIFICATIONS

PARAMETERS

VALUE

Input Voltage Range

100 VAC - 240 VAC

Output Voltage Range

11.4 - 15 VDC

Maximum Output Current (all 18 channels)

24 A

Power Output Rating

360 W

Single Channel Absolute Maximum Current Output

1.33 A 

Ingress Protection

I

P2

0

4 SPECIFICATIONS

Summary of Contents for AUTOMATE MT03-0301-411005

















Reviews: