background image

5

MIDI Setup Menu

MVC : Setup Menu

You can perform settings for MIDI Visual Control (MVC) mode here. These settings are valid when the VR-3 is placed in MVC mode 
by an MVC ON message; these settings will not affect similar settings made in Normal mode. 

If you find a value is "DFLT xxx", this is the typical value specified by the MVC standard. It can also mean the value previously 
specified by an MVC setup message.  TWhen the unit receives an MVC OFF message, any previously sent MVS setup data will 
revert to the default values of the MVC standard. This will also occur when you power cycle the VR-3.  

If you have selected the value other than [DFLT] in the menu, the MVC setup message will be ignored and the value you have set 
in the menu will take priority.

MVC : DEVICE ID

This sets Device ID to receive MVC message. 

MVC : CLIP CTRL CH

This sets Rx channel for video switching.

MVC : NOTE CTRL MODE

This sets control mode when you switch video channels using note messages. 

MVC : NOTE CTRL UPPKEY

This sets the upper key of the note when you switch video channels using note messages. 

MVC : NOTE CTRL LOWKEY

This sets the lower key of the note when you switch video channels using note messages. 

MVC : TRANSITION TIME

This sets assignment of the transition time control.

MVC : TRANSITION SEL

This sets assignment of the transition type selection. (You cannot select [DFLT] as this is out of the standard.) 

MVC : AUDIO LEVEL CTRL

This sets assignment of the output audio level control. (You cannot select [DFLT] as this is out of the standard.)

MVC : COLOR CTRL CH

This sets the Rx channel of the video output fade control. 

MVC : OUTPUT FADE CTRL

This sets assignment of the video output fade control. (You cannot select [DFLT] as this is out of the standard.) 

Summary of Contents for VR-3


























Reviews: