Rohm BP35C0-J11 Startup Manual Download Page 3

Page: 3 / 22

3/21

User’s Guide

BP35C0-J11 Start up manual

No. 63UG011E Rev.002

JUN.2020

About downloading related documents and software

The documents associated with this manual are listed at the beginning of each chapter. Please read it according to your needs.

Hardware documentation is available for download on the ROHM’s Wi-SUN support page.

ROHM Wi-SUN Support page:

https://www.rohm.com/products/wireless-communication/specified-low-power-radio-

modules/bp35c0-j11-product/documents

You can also download the software documentation on the support page of ISB Co., Ltd.

Wi-SUN Enhanced HAN + B-route support page:

https://wisun.isb.co.jp/enhan/wer0/

Use Tera Term of terminal software for operation confirmation.

You can download it from the following URL:

Tera term Download:

https://ja.osdn.net/projects/ttssh2/

The evaluation board uses FTDI's USB-UART conversion chip. It is not automatically recognized by Windows and you
may need to install the driver, so please download the FTDI driver from the following URL if necessary.

FTDI driver Download:

https://www.ftdichip.com/FTDrivers.htm

Summary of Contents for BP35C0-J11























Search results

Summary of Contents for BP35C0-J11

Reviews:

Related manuals for BP35C0-J11

Brands by name

Popular brands

Rohm BP35C0-J11, Startup Manual

Search results

Summary of Contents for BP35C0-J11

Reviews:

Related manuals for BP35C0-J11

Brands by name

Popular brands