Rohm BP35C0-J11 Startup Manual Download Page 20

Page: 20 / 22

20/21

User’s Guide

BP35C0-J11 Start up manual

No. 63UG011E Rev.002

JUN.2020

6.2.

Connect UART directly from through Hole

BP359C has a through-hole as follows.

The terminals (TXD, RXD, etc.) required for BP35C0-J11 UART can be extracted from the through-hole group 1 and through-hole

group 2 as described in on the BP359C board.

Please note that when using the UART terminal of through-hole group1, it is necessary to connect the JP1 and enable the terminal.

Through-hole 2, it is possible to take out the UART terminal from BP35C0-J11 without switching the JP1.

It is also possible to connect the BP35C0-J11 to the host MCU and the through-hole by the wiring as follows. Please try to evaluate

using the MCU without using Tera Term etc.,

* In the figure, BP35C0-J11-T01 is used, but the process is the same when using BP35C1-J11-T01.

Summary of Contents for BP35C0-J11























Search results

Summary of Contents for BP35C0-J11

Reviews:

Related manuals for BP35C0-J11

Brands by name

Popular brands

Rohm BP35C0-J11, Startup Manual

Search results

Summary of Contents for BP35C0-J11

Reviews:

Related manuals for BP35C0-J11

Brands by name

Popular brands