background image

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any 
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard 
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein 
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM 
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of 
whatsoever nature in the event of any such infringement, or arising from or connected with or related 
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or 
otherwise dispose of the same, no express or implied right or license to practice or commercially 
exploit any intellectual property rights or other proprietary rights owned or controlled by 
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.

Appendix1-Rev2.0

Thank you for your accessing to ROHM product informations. 
More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM

  Customer Support System

THE AMERICAS

 

/

 

EUROPE

 

/

 ASIA

 

/

 

JAPAN 

Contact us

 : 

webmaster @ rohm.co. jp

www.rohm.com

Copyright © 

2008 ROHM CO.,LTD.

The products listed in this document are designed to be used with ordinary electronic equipment or devices 
(such as audio visual equipment, office-automation equipment, communications devices, electrical 
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level 
of reliability and the malfunction of which would directly endanger human life (such as medical 
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers 
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance 
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow 
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in 
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM 
cannot be held responsible for any damages arising from the use of the products under conditions out of the 
range of the specifications or due to non-compliance with the NOTES specified in this catalog.

21  Saiin Mizosaki-cho, Ukyo-ku,  Kyoto 615-8585, Japan

TEL : +81-75-311-2121
FAX : +81-75-315-0172

Appendix

Downloaded from 

Elcodis.com

 

electronic components distributor

 

Summary of Contents for BH1715FVC

















Reviews: