manualshive.com logo in svg

Rohde & Schwarz TS-PIO2, User Manual

Share
Download
Rohde & Schwarz TS-PIO2 User Manual Download Page 38

Function Description

R&S

®

TS-PIO2

22

User Manual 1506.7208.12 ─ 06

●

rspio2_Disconnect

●

rspio2_DisconnectAll

Function 

rspio2_DisconnectAll

 can be used to break all connections created with

rspio2_Connect

 with a single function call.

rspio2_DisconnectAll

 has no effect on the configuration of outputs, coupling

relays, or the ground relay.

5.1.3.4

Switching outputs

Function 

rspio2_ConfigureOutputMux

 configures the switching state of the out-

puts of a channel. The following settings are possible:

●

Output disconnected

●

Output connected with front side connector (CHx_OUT1)

●

Output connected with corresponding input (CHx_IN)

Please note that function 

rspio2_DisconnectAll

 does not affect this setting!

5.1.3.5

Coupling relay

The coupling relays connect the local analog bus (LAB) on the module with the analog
bus in the R&S CompactTSVP or R&S PowerTSVP. The function

rspio2_ConfigureCoupling

 defines the status of the coupling relays.

Please note that function 

rspio2_DisconnectAll

 does not open these relays!

5.1.3.6

Ground relays

The R&S TS-PIO2 module has a ground relay that can be used to connect the poten-
tial-free module ground (AGND) with ground (GND).

 

 

 

Function description of the R&S TS-PIO2 module

Summary of Contents for TS-PIO2



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands