manualshive.com logo in svg

Rohde & Schwarz TS-PIO2, User Manual

Share
Download
Rohde & Schwarz TS-PIO2 User Manual Download Page 28

Layout

R&S

®

TS-PIO2

12

User Manual 1506.7208.12 ─ 06

4.2 Display elements of the module R&S TS-PIO2

Figure 4-2: Arrangement of the LEDs on the module R&S TS-PIO2

On the front side of the module R&S TS-PIO2 there are three LEDs which show the
current status of the module. The LEDs have the following meaning:

Table 4-2: Display elements on the module R&S TS-PIO2

LED

Description

red

Fault condition:

Lights up when a fault is detected on the R&S TSPIO2 module during the power-on test
after the supply voltage is switched on. This means that there is a hardware problem on
the module. (also see 

Chapter 8, "Self-Test"

, 

on page 41)

yellow

Communication:

Lights up when data is exchanged across the interface.

green

Supply voltage OK:

Lights up when all necessary supply voltages are present (incl. the R&S TS-PDC vol-
tages).

4.3 Mechanical layout of R&S TS-PDC

The rear I/O Module R&S TS-PDC is designed for rear installation in the R&S Com-
pactTSVP/R&S PowerTSVP. The height of the module's circuit board is 3 HE (134
mm). The module is fastened in place by two fastening screws on the front baffle plug
connector X20 connects module R&S TS-PDC with the extension backplane in the
R&S CompactTSVP/ R&S PowerTSVP. Module R&S TS-PDC must always be used
with the correct Rear-I/O slot for the main module (for example module R&S TS-PIO2).

 

 

Mechanical layout of R&S TS-PDC

Summary of Contents for TS-PIO2



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands