Rohde & Schwarz TS-PIO2 User Manual Download | Manualshive

Page: 30 / 66

background image

Layout

R&S

®

TS-PIO2

14

User Manual 1506.7208.12 ─ 06

4.4 Display elements of the R&S TS-PDC Module

4.4.1 R&S TS-PDC Version lower than 2.0 (1157.9804.02)

The actual status of the module is signalized by 8 green LEDs, whereat each LED indi-
cates the presence of an output voltage.

In fault-free operation all 8 LEDs must light up simultaneously.

4.4.2 R&S TS-PDC from Version 2.0 (1157.9804.12)

The actual status of the module is signalized by 10 LEDs.

In the switched-on state the green LED PWR indicates the power-on state. In fault-free
operation additionally the 8 green LEDs for each generated output voltage light up.

In the case of overload or over temperature the module shuts down by itself. The error
is signalized by the red LED ERR.

Figure 4-4: LEDs on the R&S TS-PDC module from Version 2.0

Display elements of the R&S TS-PDC Module

«
...
28
29
30
31
32
...
»

Summary of Contents for TS-PIO2



































































Reviews:

No comments

Related manuals for TS-PIO2

Brand: JeaTone Pages: 6

Brand: Wayne-Dalton Pages: 24

Brand: National Instruments Pages: 10

Brand: York Pages: 6

Passport 500 Pro

Brand: Fender Pages: 4

Brand: Zepro Pages: 52

Brand: Hach Pages: 504

Brand: Genie Pages: 35

Brand: AUMA Pages: 168

JCPT-HD/DC Series

Brand: DL Pages: 119

Brand: Niko Pages: 48

Brand: Purelogic Pages: 60

Brand: Watts Pages: 24

Brand: b-red Pages: 28

Brand: Wachs Pages: 224

Brand: ADLINK Technology Pages: 37

Hy-Brid Lifts HB-830CE

Brand: Custom Equipment Pages: 29

Brand: YASKAWA Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands