manualshive.com logo in svg

Rohde & Schwarz FSMR, User Manual

Share
Download
Rohde & Schwarz FSMR User Manual Download Page 16

Measurement Examples 

FSMR 

1166.3311.12-01 1.14 

E-1 

 

PRESET

1.  Measure the AM modulation depth 

Reset the instrument. 

Press the PRESET key. 

  The main receiver menu is opened. The receiver mode is set. 

DEMOD

AM

Switching to AM demodulation 

Press the DEMOD hotkey. 

 

The analog demodulation menu is displayed. 

In the DEMOD menu press the AM softkey. 

 

The modulation frequency and the AM modulation depth with 
peak detection measurement results are displayed in the lower 
window of the screen. The upper window shows the RF 
Frequency and the RF input level.

 

FILTER

LOW PASS

15 KHZ

Limiting the bandwidth - Audio Filters 

Press the 

DEMOD

 hotkey. 

  The analog demodulation menu is displayed. 

In the DEMOD menu press the 

FILTER

 softkey. 

  The audio filter menu is displayed. To suppress unwanted 

broadband noise or harmonics of the demodulated signal, the 
bandwidth of the measurement can be limited with highpass and 
lowpass filters. 

In the FILTER menu press the 

LOW PASS

 

15 KHZ 

softkey. 

 

The following screen is displayed: 

Fig.1-10 

AM Modulation measurement in the 

DEMOD

 mode 

 

In the FILTER menu press the LOW PASS 15 KHZ softkey again 
to switch the filter off.

 

Summary of Contents for FSMR






















Reviews:

No comments

Brands by name

Popular brands

Load more brands