background image

Security Locks SL2000F and SL2000F-VP EN 

 

2020-05-06 

 

Page 

5

 of 

12

 

 

 

Commands 

Commands can be entered during normal working time of a SL2000 and doesn’t require entry to the 

programming mode.  

[USER Code] [#] 

Whenever a valid USER code is entered the code lock generates two beeps (**) and then starts count C1C2 
time delay. After it passes SL2000 activates Door Lock (momentary) output for the time defined by C3C4 

settings. 

[MASTER Code] [#] 

Each time the MASTER code is entered the SL2000 changes its arming mode (switches from Armed to Disarmed 

mode or in reverse direction). 

[INSTALLER Code] [#] 

After this command code lock generates two beeps (**) and enters  the Installer Programming mode. In this 

mode installer can manage (add, modify or delete) the USER codes. 

[*] [Old INSTALLER Code] [#] [New INSTALLER Code] [#] 

This command erases the current INSTALLER code and program a new one. If command is successfully 

accomplished the unit generates three series of two beeps (** ** **). 

[*] [Old MASTER Code [#][New MASTER Code] [#] 

This command erases the current MASTER code and program a new one. If command is successfully 
accomplished the unit generates three series of two beeps (** ** **). 

 
[#]  

Normally pressing [#] is used to mark the end of the code but when pressed separately for a time longer the 
0.5s it triggers Door Bell indication.  

Programming The USER Codes 

The SL2000 enables programming of up to 55 different USER codes. The USER codes can be managed 
(added/deleted/changed) only in the Installer Programming mode (to enter Installer Programming mode press: 

[INSTALLER Code]+[#]). Once in the Installer Programming mode you have following commands: 
 

[0] [1] [#] [code] [#]

  

- Programming of the USER code no. 1 

[0] [2] [#] [code] [#]

  

- Programming of the USER code no. 2 

[0] [3] [#] [code] [#]

  

- Programming of the USER code no. 3 

...etc. 
...etc. 
...etc. 

[5] [5] [#] [code] [#]  

-

 Programming of the USER code no. 55 

[0] [0] [#]    

 

Delete all USER codes 

[9] [9] [#] [code] [#]

  

- Deletes the code entered in square brackets 

[#]  

 

 

 

-

 Exit from the Installer Programming mode 

When the SL2000 accepts the new USER code it generates two series of two beeps (** **). Any attempt to 
program the USER code which already exists in the memory or to program it with a wrong length then will 

cause the programming error signaled by a long acoustic beep.  

Note: The SL2000 enables programming of maximum 55 USER codes, each of them can be used to trigger  
Door Lock output. 

Note: Whenever you re-program MASTER or INSTALLER code remember that new code programmed into a unit 

must have the same length as the old one. 

Summary of Contents for SL2000F













Reviews: