background image

HRT82TS Installation Guide Rev.C.doc

 

2016-10-10 

 

 

4/9 

 

3.3 RACS CLK/DTA communication bus 

RACS CLK/DTA is the addressable bidirectional communication standard developed and applied in 
Roger controllers in order to enable their communication with peripheral devices. Addresses of all 

devices connected to CLK and DTA lines must be properly configured in range of 00..15. Standard 
unshielded  signal  cables (e.g. U/UTP cat. 5)  with maximal length of 150m can be used  for RACS 

CLK/DTA communication. 

3.4 Front panel 

HRT82TS is equipped with front icon backlight which is used for signalling proper operation (steady 
light) or communication problems (blinking). 

3.5 Wall mounting and installation guidelines 

HRT82TS  consists  of  front  panel  and  base  which  are  factory  assembled  and  require  manual 
disassembly prior to installation according to fig. 4. 

Installation guidelines 

 

Install device on wall far from sources of heat and moisture 

 

It is recommended to install device on Ø60mm flush mounting box 

 

Front  panel  and  base  must  be  properly  oriented  in  order  to  ensure  functioning  of  tamper 
resistance. 

 

All electric connections must be made with power supply switched off 

 

Run connection wires through hole in device base and then connect wires to screw terminals 

 

If  device  and  controller  are  supplied  from  different  power  supply  units  then  it  is  necessary 
connect GND terminals of both devices 

 

Front panel can be regularly cleaned with wet cloth and mild detergent. Do not clean by means 
of abrasive materials and strong cleaners like alcohols, solvents, etc. 

 

Damages resulting from improper maintenance or use are not covered by warranty 

 

Summary of Contents for HRT82TS










Reviews: