background image

HRT82TS Installation Guide Rev.C.doc

 

2016-10-10 

 

 

7/9 

 

 

Fig. 6 Device select window in RogerVDM software 

 

Fig. 7 Configuration window in RogerVDM software 

Table 3. Configuration parameters  

Parameter 

Values 

Description 

General 

Device Name 

16 ASCII 
characters 

Device description which can be filled with any comment by 
installer. 

Transmission Format 

RACS CLK/DTA 
Reader Address 

0..15 

Device address on RACS CLK/DTA bus. Default address ID=7 
is required for communication with HRC controller. 

Communication 

timeout 

0..255 

The device signals communication failure when selected 

timeout [0.5s] elapses. When 0 is selected then failure is not 
signalled at all. 

 

4.2 Firmware update 

HRT82TS firmware can be updated with RogerVDM (available at 

www.roger.pl

) after connection to 

RUD-1 communication interface. 

Firmware update procedure 

1.

 

Connect device to RUD-1 communication interface according to fig. 5 

2.

 

Install and start RogerVDM software 

3.

 

Close 

Select Device window 

4.

 

In top menu select 

Tools->Update firmware 

5.

 

In the opened window select device, port with connected RUD-1 and specify path to firmware 

file (*.hex) – see fig. 8 

6.

 

According  to displayed  message place jumper  on FDM pins and  restart the device (place and 

remove jumper on RST pins or switch power supply off and on) 

7.

 

Select 

Update button 

8.

 

After  firmware  upload  remove  jumper  from  FDM  pins  and  reset  device  (place  and  remove 

jumper on RST pins or switch power supply off and on) 

 

Summary of Contents for HRT82TS










Reviews: