background image

HRT82MF-CH Installation Guide.doc

 

2018-09-21 

 

 

11/11 

 

6.

 

O

RDERING INFORMATION

 

Table 5. Ordering information 

HRT82MF-CH  MIFARE hotel card holder 

RUD-1 

Communication interface with 12VDC power supply output 

 

7.

 

P

RODUCT HISTORY

 

Table 6. Product history 

Version 

Released 

Description 

HRT82MF-CH v.1.0  07/2014 

The first commercial version of the product 

 
 

 
 
 

 
 

 
 
 

 
 

 
 

 

 

This symbol placed on a product or packaging indicates that the 
product should not be disposed of with other wastes as this may 

have a negative impact on the environment and health. The user 
is obliged to deliver equipment to the designated collection points 

of electric and electronic waste. For detailed information on 
recycling, contact your local authorities, waste disposal company 
or point of purchase. Separate collection and recycling of this type 

of waste contributes to the protection of the natural resources 
and is safe to health and the environment. Weight of the 

equipment is specified in the document. 

 
 
 

Contact: 

Roger sp. z o.o. sp.k. 

82-400 Sztum 

Gościszewo 59 

Tel.: +48 55 272 0132 
Fax: +48 55 272 0133 

Tech. support: +48 55 267 0126 

E-mail: 

[email protected]

 

Web

www.roger.pl

 

Summary of Contents for HRT82MF-CH












Reviews: