roco 62366 Operating Instructions Manual Download Page 8

8

GB

Introduction

Congratulations on the purchase of a  ROCO Locomo-
tive with built-in Sounddecoder. At last with Sound-
decoder  your  locomotives  will  sound  just  like  the 
prototype.  You  will  soon  notice  that  locomotives 
equipped with

 

Sounddecoders are always the centre 

of attention.
The decoders are basically supplied with the address 
setting  ”03”  (both  for  NMRA/DCC,  and  also  for 
Motorola**).
The 

reset 

facility  is  convenient: You  can  call  up  the 

original  factory  values

  again  at  any  time  both  in 

DCC and in Motorola** operation. To do this write 

an 

8 in CV 8 or an 08 in Register 08

 

(see „Possible 

settings in DCC digital operation“ CV 8 or “Possi-
ble settings in Motorola** digital operation“, ).

Please note the following warnings:

•  Sounddecoders  may  only  be  used  with  model 

railways.

•  Avoid jolts and exerting pressure on the decoder 

and do not expose it to moisture.

•   The decoder installed in your ROCO locomotive has 

been  specifically  adapted  for  this  locomotive  and 
must be used only in this particular locomotive.

•  Always disconnect the power supply to the decod-

er before doing any work on it.

•  Should it be necessary to remove the loudspeaker 

for  maintenance  work,  handle  the  loudspeaker 
extremely  carefully:  do  not  put  any  pressure  on 
it.

Characteristics of the Sounddecoders

Multi-protocol operation:

 

The  Sounddecoder  understands  and  automatically 
recognizes  both  the  widely  used  Märklin*/  Motoro-
la**  format  and  also  the  NMRA/DCC  system  based 
format. 

The decoder 

  Can run on direct current (DC) or alternating cur-

rent (AC) 

analogue

 (

sound possible

)

  is 

load-regulated

: in digital operation the speed 

is  maintained  at  the  same  regulator  setting  up 
and down grade and with different train loads,

 

has 

overload  protection

  for  the  all  function 

outputs,

 

Recognises 

braking sections

 from Rocco as well 

as systems from Zima, Lenz, and Märklin*

Preset address:  

  DCC/NMRA:   03

 

 

Motorola**:  03

*  „ Märklin” ist ein eingetragenes Warenzeichen der 
      Gebr. Märklin & Cie. GmbH, Göppingen
**   „Motorola” ist ein eingetragenes Warenzeichen der Motorola Inc., 

Tempe-Phoenix (Arizona/USA)

63931923.indd   8

30.06.2011   11:41:17

Summary of Contents for 62366

































Reviews: