manualshive.com logo in svg

Rockwell Automation Allen-Bradley 150-E, Manual, Page: 21 / 32

Share
Download
Rockwell Automation Allen-Bradley 150-E Manual Download Page 21

Rockwell Automation Publication 150-UM009E-EN-P - August 2021

21

Chapter 3          Programming

Motor FLA Requirements

The front of the SMC controller contains a dial that is used for setting the 
actual FLA of the motor. The label is designed to accommodate motors 
connected in the line or Delta mode. To determine the proper setting, look at 
the motor’s nameplate and set the dial accordingly. The dial setting can be 
modified depending on the service factor of the motor. 

Figure 11 - Motor FLA Setting

Table 13 - Overload Trip Class

Setting

Switch #11

Switch #12 Description

OFF

OFF

OFF

The controller incorporates, as standard, electronic overload 
protection. This motor overload protection is accomplished 
electronically by using internal current transformers on each of the 
three phases.

10

ON

OFF

15

OFF

ON

20

ON

ON

Table 14 - Overload Reset

Setting

Switch #13 Description

Manual

OFF

In manual reset mode, the fault can only be reset by pushing the ‘Push to Reset’ button 
on the front of the controller. In auto reset mode, the unit automatically resets when 
the unit determines the motor has cooled to 75% of its thermal capacity.

Auto

ON

Table 15 - Aux #1 Setting

Setting

Switch #14 Description

Normal

OFF

The operation defines the operation of the auxiliary contacts. Normal mode means 
that the contact changes state immediately when a start/run command is given. 
Up-to-Speed mode means that the contact changes state only when the controller 
is in bypass. Aux#2, when added, operates opposite of this programming.

Up-to-Speed

ON

Table 16 - Motor Connection Type

Setting

Switch #15 Description

Delta

OFF

In Delta connection mode, the device is designed to control a 6- or 12-lead motor. In line 
connection mode, the device is designed to control a 3- or 9-lead motor.

Line

ON

Table 17 - Stop Delay

Setting [seconds]

Switch #16 Description

0.0

OFF

When the delay is programmed, the motor continues to run for the 

programmed period of time after the run command is removed from the 

controller.

0.75

ON

∆ 32

19

Delta FLA

Line FLA

∆ 11

7

∆ 22

13

Service Factor _ _

FLA _ _

Service Factor < 1.15

Service Factor ≥ 1.15

= 0.9 X FLA

= 1.0 X FLA

= 1.0 X FLA

OR

Maximum Continuous Rated

(MCR) Motors

Summary of Contents for Allen-Bradley 150-E

































Reviews:

No comments