Robustel EG8001 Page 30 User Manual Download

Page: 30 / 88

Robustel EG8001 User Guide

RT_UG_EG8001_v.1.0.1 2 June, 2017 29/84
Confidential

3.6

Interface > Link Manager

General Settings @ Link Manager

Item

Description

Default

Link

It’s no need to configure link manually in this part, we recommend to remain
the default setting of system.

WWAN1

Emergency Reboot

Enable to reboot the whole system if no links available.

OFF

Note:

Click

for help.

Link Settings

allows you to configure the parameters of Cellular link connection. It is recommended to enable Ping

detection to keep the gateway always online. The Ping detection increases the reliability and also costs the data
traffic.

Click

on the right-most of WWAN1 to enter the configuration window.

WWAN1

The window is displayed as below when enabling the “Automatic APN Selection” option.

Summary of Contents for EG8001

























































































Search results

Summary of Contents for EG8001

Reviews:

Related manuals for EG8001

Brands by name

Popular brands

Robustel EG8001, User Manual

Search results

Summary of Contents for EG8001

Reviews:

Related manuals for EG8001

Brands by name

Popular brands