Robustel EG8001 Page 18 User Manual Download

Page: 18 / 88

Robustel EG8001 User Guide

RT_UG_EG8001_v.1.0.1 2 June, 2017 17/84
Confidential

2.5

Insert or Remove SIM Card

Be sure to insert a SIM card before you use the gateway.

Insert or remove the SIM as shown in the following steps.



Inserting SIM Card

Power off the gateway.

Use a pointed stick to press the Push Button, and then take out the SIM Card Tray.

Place the SIM card on the tray, and insert them to the slot until you hear “a cracking sound”.



Removing SIM card

Power off the gateway.

Press the Push Button, and the tray with SIM card will pop up to be pulled out.

Note:

Don’t touch the metal surface of the SIM card in case information in the card is lost or destroyed.

Don’t bend or scratch your SIM card. Keep the card away from electricity and magnetism.

Make sure to disconnect the power source from your gateway before inserting and removing your SIM card.

Summary of Contents for EG8001

























































































Search results

Summary of Contents for EG8001

Reviews:

Related manuals for EG8001

Brands by name

Popular brands

Robustel EG8001, User Manual

Search results

Summary of Contents for EG8001

Reviews:

Related manuals for EG8001

Brands by name

Popular brands