Robus Black Star 10 Comfort Manual Download Page 4

 

 

Robus Energy Ltd 

 

4 of 26 

MCS 0001RE 

Issue 2.1 

March 2014 

 

The Clean Air Act 1993 and Smoke Control Areas

 

 

The  Robus  Black  Star  Comfort  range  of  boilers  listed  below  has  been  recommended  as  suitable  for  use  in 
smoke  control  areas.  The  recommended  fuel  for  the  boiler  is  6mm  or  8mm  diameter  wood  pellets  to  EN 
14961 Part 2 class A1 wood pellets only. 

 

Robus Black Star 10 Comfort 
Robus Black Star 14 Comfort 
Robus Black Star 24 Comfort 
Robus Black Star 45 Comfort 

 

Under the Clean Air Act local authorities may declare the whole or part of the district of the authority to be a 
smoke control area. It is an offence to emit smoke from a chimney of a building, from a furnace or from any 
fixed boiler if located in a designated smoke control area. It is also an offence to acquire an "unauthorised fuel" 
for use within a smoke control area unless it is used in an "exempt" appliance ("exempted" from the controls 
which generally apply in the smoke control area).  

 

The  Secretary  of  State  for  Environment,  Food  and  Rural  Affairs  has  powers  under  the  Act  to  authorise 
smokeless  fuels  or  exempt  appliances  for  use  in  smoke  control  areas  in  England.  In  Scotland  and  Wales  this 
power rests with Ministers in the devolved administrations for those countries. Separate legislation, the Clean 
Air (Northern Ireland) Order 1981, applies in Northern Ireland. Therefore it is a requirement that fuels burnt or 
obtained  for  use  in  smoke  control  areas  have  been  "authorised"  in  Regulations  and  that  appliances  used  to 
burn solid fuel in those areas (other than "authorised" fuels) have been exempted by an Order made and signed 
by the Secretary of State or Minister in the devolved administrations. 
 

 

Further 

information 

on 

the 

requirements 

of 

the 

Clean 

Air 

Act 

can 

be 

found 

here 

http://smokecontrol.defra.gov.uk/

  

 

Your  local  authority  is  responsible  for  implementing  the  Clean  Air  Act  1993  including  designation  and 
supervision of smoke control areas and you can contact them for details of Clean Air Act requirements”

 

Fuel and warranty 

The Robus Black Star and Robus Black Star Comfort  pellet boilers are designed for use  with EN-plus A grade 
wood  pellets  only.  The  use  of  substandard  fuels  will  compromise  the  efficiency,  reduce  the  life  span  and 
invalidate the warranty of the appliance.  

What is EN-Plus? 

 

EN-Plus is the European Quality Standard for the manufacture and supply of wood pellets. Manufacturers and 
Distributors who have the EN-Plus standard have been certified as meeting the required quality standards and 
they are entitled to display the EN-Plus logo and their own unique License Number.

 

Summary of Contents for Black Star 10 Comfort



























Reviews: