ROBUA G Series Installation, Use And Maintenance Manual Download Page 6

Page: 6 / 48

Warnings

III

III.2

CONFORMITY

EU directives and standards

The G series gas unit heaters are certified in accordance

with European regulation GAR 426/2016/EU and meet the

essential requirements of the following Directives:

▶

2016/426/EU "Gas Appliances Regulation" as amend-

ed and added.

▶

2014/30/EC "Electromagnetic Compatibility Directive"

as amended and added.

▶

2014/35/EC "Low Voltage Directive" as amended and

added.

▶

2006/42/EC "Machine Directive" as amended and add-

ed.

▶

2281/2016/EU "Ecodesign requirements for air heat-

ing products" as amended and added.

Furthermore, they comply with the requirements of the

following standards:

▶

EN 1020 Non-domestic forced convection gas-fired air

heaters for space heating not exceeding a net heat in-

put of 300 kW incorporating a fan to assist transporta-

tion of combustion air or combustion products.

▶

prEN 17082 Domestic and non-domestic gas-fired

forced convection air heaters for space heating not ex-

ceeding a net heat input of 300 kW.

Other applicable provisions and standards

The design, installation, operation and maintenance of

the systems shall be carried out in compliance with cur-

rent applicable regulations, depending on the Country

and location, and in accordance with the manufacturer's

instructions. In particular, regulations regarding the fol-

lowing shall be complied with:

▶

Gas systems and equipment.

▶

Electrical systems and equipment.

▶

Heating systems.

▶

Environmental protection and combustion products

exhaust.

▶

Fire safety and prevention.

▶

Any other applicable law, standard and regulation.

III.3

EXCLUSIONS OF LIABILITY AND

WARRANTY

Any contractual or extra-contractual liability of the

manufacturer for any damage caused by incorrect

installation and/or improper use and/or failure to

comply with regulations and with the manufactur-

er's directions/instructions shall be disclaimed.

In particular, the warranty on the appliance may be

rendered void by the following conditions:

Incorrect installation.

Misuse.

Failure to comply with the manufacturer's indica-

tions on installation, use and maintenance.

Alteration or modification of the product or any

part thereof.

Extreme operational conditions or however out-

side of the operational ranges set forth by the man-

ufacturer.

Damages caused by external agents such as salts,

chlorine, sulphur or other chemical substances

present in the air of the installation site.

Abnormal actions transmitted to the appliance by

the system or installation (mechanical stresses,

pressure, vibrations, thermal expansion, electrical

surges...).

Accidental damages or due to force majeure.

Summary of Contents for G Series

















































Search results

Summary of Contents for G Series

Reviews:

Related manuals for G Series

Brands by name

Popular brands

ROBUA G Series, Installation, Use And Maintenance Manual

Search results

Summary of Contents for G Series

Reviews:

Related manuals for G Series

Brands by name

Popular brands