background image

The Robertshaw

®

 Programmable WiFi Thermostat allows you to control the temperature 

anytime and anywhere. It features a large backlit display and LCD touchscreen for ease of 
operation. Compatible with any IOS or Android Smartphone.

Thermostat System Types

Power Options

Hardwire (Common Wire) only

Gas, Oil, or Electric Heat with Air Conditioning
Heat Pumps (without auxiliary or emergency heat)
Multi-Stage Systems
Heat-Only, including for Floor and Wall-Furnace
Cool-Only
750 Millivolt Heating Systems

INSTALLATION MANUAL

1

IMPORTANT SAFETY INFORMATION 
WARNING: 

•  Always turn off power at the main power source 

by unscrewing fuse or switching circuit breaker 
to the off position before installing, removing, 
cleaning, or servicing thermostat. 

•  Read all of the information in this manual before 

installing or programming this thermostat. 

•  This is a 24V AC low voltage thermostat. Do not 

install on voltages higher than 30V AC. 

•  All wiring must conform to local and national 

building and electrical codes and ordinances.

•  Do not short (jumper) across terminals on 

the gas valve or at the system control to test 
installation. This will damage the thermostat and 
void the warranty.

Summary of Contents for RS10420T

































Reviews: