Robe Robin square User Manual Download Page 4

Page: 4 / 40

Do not touch the internal side of the yoke when fixture head is moving (tilt movement).

There is a danger of injury of your fingers.

2. Operating determination

This device is a moving head for creating decorative effects and was designed for indoor use only.

This device is for professional use only. It is not for household use.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched off until

it has reached room temperature.

Do not shake the device. Avoid brute force when installing or operating the device.

Never lift the fixture by holding it at the projector head, as the mechanics may be damaged. Always hold the

fixture at the transport handles.

When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture

or dust. There should not be any cables lying around. You endanger your own and the safety of others!

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fix

ture.

Always secure the fixture with an appropriate safety wire.

Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fas

tened.

The maximum ambient temperature 40°C must never be exceeded.

To avoid damage of the internal optical system of the fixture, never let the sunlight

lights directly to the lens array, even when the fixture is not working !

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualified for operating the device. Most damages are the result of unprofessional operation!

Please use the original packaging if the device is to be transported.

Please consider that unauthorized modifications on the device are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-

circuit, burns, electric shock, burns etc.

Summary of Contents for Robin square









































Search results

Summary of Contents for Robin square

Reviews:

Related manuals for Robin square

Brands by name

Popular brands

Robe Robin square, User Manual

Search results

Summary of Contents for Robin square

Reviews:

Related manuals for Robin square

Brands by name

Popular brands