Robe Robin 300E Spot User Manual Download Page 6

Page: 6 / 39

4. Installation

Fixtures must be installed by a Qualified electrician in accordance with all

national and local electrical and construction codes and regulatio

4.1 Connection to the mains

For protection from electric shock, the fixture must be earthed!

The Robin 600E Spot is equipped with auto-switching power supply that automatically adjusts to any 50/60Hz

AC power source from 100-240 Volts.

For use with 100-120 V supplies, both main 8 A fuses has to be exchanged for 15 A fuses which are

enclosed in the packing.

To install the 15 A fuses:

1. Disconnect the fixture from AC power.

2. Unscrew the "live" fuse holder on the rear panel of the base with a flat-tip screwdriver from the housing

(anticlockwise).

3. Remove the 8 A fuse from the fuse holder.

4. Put the 15 A fuse in the fuse holder.

5. Replace the fuse holder in the housing and screw it fully clockwise.

6. Repeat steps 2-5 for the "neutral" fuse holder

Install a suitable plug on the power cord, note that the cores in the power cord are coloured according to the

following table. The earth has to be connected!

If you have any doubts about proper installation, consult a qualified electrician.

Core (EU)

Core (US)

Connection Plug Terminal Marking

Brown

Black

Live

Light blue

White

Neutral

Yellow/Green Green

Earth

Summary of Contents for Robin 300E Spot








































Search results

Summary of Contents for Robin 300E Spot

Reviews:

Related manuals for Robin 300E Spot

Brands by name

Popular brands

Robe Robin 300E Spot, User Manual

Search results

Summary of Contents for Robin 300E Spot

Reviews:

Related manuals for Robin 300E Spot

Brands by name

Popular brands