background image

RLH Industries, Inc.

936 N. Main Street, Orange, CA 92867

Phone: 800-877-1672

FAX: 714-532-1885

email: [email protected]

www.fiberopticlink.com

Fiber Optic Link

RLH Industries, Inc.

The leader in

rugged, fiber op�c

technology

USER GUIDE

General Safety Practices

Guidelines for Handling Terminated Fiber Cable

CAUTION - SEVERE SHOCK HAZZARD

The equipment discussed in this document may require tools designed for the purpose being described. RLH
recommends that service personnel be familiar with the correct handling and use of any installa�on equipment used,
and follow all safety precau�ons including the use of protec�ve personal equipment as required.

Do not bend fiber cable sharply; use gradual and smooth bends to avoid damaging glass fiber

Keep dust caps on fiber op�c connectors at all �mes when disconnected

Do not remove dust caps from unused fiber

Keep fiber ends and fiber connectors clean and free from dust, dirt and debris; contamina�on will cause signal loss

Do not touch fiber ends

Store excess fiber on housing spools or fiber spools at site

Never install during a lightning storm or where unsafe high voltages are present

Use cau�on when handling copper wiring and follow appropriate safety regula�ons

Name

Descrip�on

TX

Transmit

RX

Receive

PWR

Power

NC

Normally Closed

Com

Common

NO

Normally Open

TRX

4~20mA Transmi�er

RCV

4~20mA Input/Receiver

Sinking

Does not provide signal voltage or current, expects the voltage and current to be present on the signal line

Sourcing

Provides signal voltage and current

Commonly Used Acronyms & Abbreviations

Summary of Contents for Analog Signal 4~20mA Fiber Link System












Reviews: