RKI Instruments GasWatch 3 Operator'S Manual Download Page 8

Page: 8 / 95

8 • Chapter 1: Introduction

GasWatch 3 for CO and O

About this Manual

The

GasWatch 3 Operator’s Manual

uses the following conventions for notes, cautions, and

warnings.

NOTE:

Describes additional or critical information.

CAUTION:

Describes potential damage to equipment.

WARNING:

Describes potential danger that can result in injury or death.

Continuous

Operating

Hours

@ 25 °C

2,000 hours in Measuring Mode (Non Alarm Operation, Fully Charged)

Case

High-impact Plastic, RF Shielded, Dust and Weather Proof (IP66/68)

Standard

Accessories

• Alligator clip

Optional

Accessories

• Watch band
• Calibration cup
• Datalogging and Setup Programs (Windows

7, 8, and 10), available at

www.rkiinstruments.com/gw3

• IrDA/USB Cable for connecting to a computer when using the Datalogging and Setup

Programs (not needed if computer has an infrared port)

Dimensions
and Weight

Approximately 42(H) x 63(W) x 22(D) mm (1.7”H x 2.5”W x 0.9”D)

Approximately 45 g (1.6 oz.)

Summary of Contents for GasWatch 3
































































































Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands

RKI Instruments GasWatch 3, Operator'S Manual

Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands