RKI Instruments GasWatch 3 Operator'S Manual Download Page 14

Page: 14 / 95

14 • Chapter 3: Measuring Mode

GasWatch 3 for CO and O

Chapter 3: Measuring Mode

Overview

This chapter explains how to use the GasWatch 3 to perform confined space entry monitoring

or general area monitoring in Measuring Mode.

Start Up

This section explains how to start up the GasWatch 3, get it ready for operation, and turn it off.

Turning On the GasWatch 3

To illustrate certain functions, the following description of the GasWatch 3 start up sequence

assumes that the following items in User Mode are turned on:

LUNCH

CAL.RMDR

, and

BP.RMDR

in User Mode, and

ID DISP

and

A.ZERO

in Maintenance Mode. If any of these

items are turned off, then the corresponding screens do not appear.
1. Press and briefly hold down POWER/MODE. Release the button when you hear a beep.
2. If

LUNCH

is set to

(factory setting if

OFF

, see pg.65), the Lunch Break Screen

appears. The unit counts down from 5 seconds.

a. Continue Accumulating: To continue accumulating peak and time-weighted average

(TWA) readings from the last time the GasWatch 3 was used, press and release

POWER/MODE or allow the countdown to reach 0. The short-term exposure limit

(STEL) reading is reset each time the GasWatch 3 is turned on.

b. Reset Accumulation: To reset the accumulation of peak and time-weighted average

(TWA) readings, press and release AIR before the countdown reaches 0.

RESUME

SEC

YES .MODE

SEC

NO .AIR

SEC

Summary of Contents for GasWatch 3
































































































Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands

RKI Instruments GasWatch 3, Operator'S Manual

Search results

Summary of Contents for GasWatch 3

Reviews:

Related manuals for GasWatch 3

Brands by name

Popular brands