RKI Instruments GasWatch 3 Operator'S Manual Download Page 16 | Manualshive

Page: 16 / 95

background image

16 • Chapter 3: Measuring Mode

GasWatch 3 for CO and O

2

4. If

BP.RMDR

is set to

ON

(factory setting is

OFF

) and a bump test is due, the screen that

appears next depends on how

BP.EXPD

is set in User Mode (see pg.62). The three

possible screens are described below. If a bump test is not due, the instrument displays the

number of days left until a bump test is due.

5. The Date/Time Screen appears for a few seconds.

BP.EXPD

set to

CONFIRM

(factory setting)

BP.EXPD

set to

CANT.USE

BP.EXPD

set to

NONE

LCD

Sound

Buzzer sounds double pulsing
tone

Buzzer sounds double pulsing
tone

None

Action

• Option A, Perform bump test:

Press and release POWER/
MODE to enter User Mode
and perform a bump test. The
instrument takes you straight
to the bump test start screen in
User Mode’s BUMP item. See
pg.37 for bump test
instructions.

NOTE

: If

Password Protection

is set ton

On

(factory setting is

Off

) using the GW-3 Config Pro

-

gram, you will be prompted for a
password to enter User Mode.

If the bump test is successful,
the screen above will not
appear again until the unit is
due for bump testing. If the
bump test is not successful,
the screen above will again
appear in the startup sequence.

• Option B, Bypass message: To

continue without performing a
bump test, press and release
AIR.

The GasWatch 3 cannot be used
until a successful bump test is
performed. Press and release
POWER/MODE to enter User
Mode and perform a bump test.
The instrument takes you
straight to the bump test start
screen in User Mode’s BUMP
item. If you don’t press
POWER/MODE, the instrument
automatically goes to the bump
test start screen after 6 seconds.
See pg.37 for bump test instruc

-

tions.

NOTE

: If

Password Protection

is set ton

On

(factory setting is

Off

) using the GW-3 Config Pro

-

gram, you will be prompted for a
password to enter User Mode.

If the bump test is successful, the
screen above will not appear
again until the unit is due for
bump testing. If the bump test is
not successful, the screen above
will again appear in the startup
sequence.

• Option A, Perform bump test:

If you want to enter User
Mode and perform a bump
test, press and release
POWER/MODE. The
instrument takes you straight
to the bump test start screen in
User Mode’s BUMP item.

• Option B, Bypass message:

To continue without
performing a bump test, wait
a few seconds for the
instrument to continue with its
startup sequence.

BP - LMT

CAL

BP - LMT

FAIL

NEXT .BP

d

0

10:42

2 . 13

2019

«
...
14
15
16
17
18
...
»

Summary of Contents for GasWatch 3
































































































Reviews:

No comments

Related manuals for GasWatch 3

Brand: DuraMax Pages: 40

GASMAX II + GDS-IR

Brand: GDS Corp Pages: 56

Brand: Cheetah Pages: 2

AERASGARD AC02-SD-TYR2

Brand: S+S Regeltechnik Pages: 16

Brand: Smart Sensor Pages: 2

Brand: Tecno Control Pages: 9

Brand: Tecno Control Pages: 9

M-59 Treasure Master

Brand: White’s Electronics Pages: 8

Coinmaster 2/DB

Brand: White’s Electronics Pages: 8

Brand: White’s Electronics Pages: 32

Brand: White’s Electronics Pages: 29

HONEYWELL BW MICROCLIP Series

Brand: Rae Pages: 2

Brand: Garrett Pages: 56

Brand: Uniden Pages: 28

Brand: makro Pages: 30

Brand: Mircom Pages: 2

Brand: SENKO Pages: 9

Brand: SENKO Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands