RKI Instruments 35-3001A-10 Operator'S Manual Download Page 29

Page: 29 / 29

35-3001A-10 Oxygen/Carbon Monoxide Sample-Draw Detector • 29

Parts List

Table 4 lists replacement parts and accessories for the sample-draw detector.

Table 4: Parts List

Part Number

Description

06-1248RK

Sample tubing, 3/16” ID x 5/16” OD, specify length

06-1248RK-03

Sample tubing, 3/16” ID x 5/16” OD, 3 feet (for calibration kit)

07-0053RK

Gasket for oxygen and CO sensor flow blocks

17-2670

Inlet fitting O-ring

17-2671

Inlet fitting front ferrule

17-2672

Inlet fitting back ferrule and tube nut

30-1016RK

Pump

33-0165RK

Hydrophobic filter

33-0167RK

Particle filter

57-0140RK

CO amplifier

57-1064RK-11

Oxygen amplifier

71-0558

Operator’s Manual, 35-3001A-10 Sample-Draw Detector

81-0064RK-01

Calibration cylinder, 50 ppm CO in air, 34 liter steel

81-0064RK-03

Calibration cylinder, 50 ppm CO in air, 103 liter

81-0076RK-01

Zero air calibration cylinder, 34 liter steel

81-0076RK-03

Zero air calibration cylinder, 103 liter

81-0078RK-01

Calibration cylinder, 100% nitrogen, 34 liter steel

81-0078RK-03

Calibration cylinder, 100% nitrogen, 103 liter

81-1054RK

Regulator, demand flow, for 34 liter aluminum, 58 liter, and 103 liter
calibration cylinders (cylinders with internal threads)

81-1055RK

Regulator, demand flow, for 17 liter and 34 liter steel calibration cylinders
(cylinders with external threads)

ES-1531-CO

Carbon monoxide sensor

OS-B11

Oxygen sensor

Summary of Contents for 35-3001A-10






























Search results

Summary of Contents for 35-3001A-10

Reviews:

Related manuals for 35-3001A-10

Brands by name

Popular brands

RKI Instruments 35-3001A-10, Operator'S Manual

Search results

Summary of Contents for 35-3001A-10

Reviews:

Related manuals for 35-3001A-10

Brands by name

Popular brands