RivieraPool Penta P, Instructions For Installation And Use Manual

Page: 7 / 16

7
Start up and use
2.8.7 Operating mode
2.8.8 Setting the time
2.8.9 Programming the filter
optimally
2.8.10 Preset filter cycles
warm
Mode cool
Blower
Jet 1 Jet 2
Light
warm
Mode cool
Blower
Jet 1 Jet 2
Light
Mode/Prog: This control button is used to switch between the three operat-
ing modes – STAnDARD, ECOnOMY and SLEEP. To program the mode, press
the „Mod/Prog“ button, then press „Cool“ to switch through to the desired
mode (LCD light flashes to acknowledge), and finally „Mode/Prog“ to confirm
the choice.
Standard mode (STANDARD). in this mode the desired water temperature is
maintained. Please note that the temperature measured last only shows when
the pump has run for at least 2 minutes. „STAnDARD“ remains displayed until
a different mode is selected.
Economy mode (ECONOMY). in this mode the water is only heated up to the
desired temperature during the filter cycles. „ECOnOMY“ remains displayed
until a different mode is selected. By pressing „Jet 1“ in economy mode, the
system switches from standard to economy (STAnDARD-in-ECOnOMY): This
mode is like the standard mode, but changes automatically after one hour to
the economy mode. By pressing „Mode/Prog“ during this time, the system is
switched to economy immediately.
Sleep mode (SLEEP). in this mode the water is only heated up during the filter
cycles to within 11º C (20º F) below the desired temperature. „SLEEP“ remains
displayed until the mode is being changed.
STANDBY: By pressing „Warm“ or „Cool“ and then „Jets 2“ the whirlpool func-
tions are temporarily turned off. This is useful when a filter has to be replaced.
The whirlpool starts up again by pressing any button.
Please Note: An electrical blocking mechanism makes it impossible for the
heater to work at the same time as the massage pumps or blower. if they are
switched on, the heater automatically switches itself off. As soon as the pumps
are switched off, the heater switches itself on again. The minimum set-point
temperature is 26º C.
When the whirlpool is switched on, the „SET TiME“ message flashes in the
display. To set the time, press first
warm
Mode cool
Blower
Jet 1 Jet 2
Light
, then
warm
Mode cool
Blower
Jet 1 Jet 2
Light
and finally
warm
Mode cool
Blower
Jet 1
Jet 2
Light
or
warm
Mode cool
Blower
Jet 1
Jet 2
Light
. Once
warm
Mode cool
Blower
Jet 1
Jet 2
Light
or
warm
Mode cool
Blower
Jet 1 Jet 2
Light
has been pressed, the time changes by intervals of one minute. Press
warm
Mode cool
Blower
Jet 1 Jet 2
Light
or
warm
Mode cool
Blower
Jet 1 Jet 2
Light
again to stop the time from changing any more. Press
warm
Mode
cool
Blower
Jet 1 Jet 2
Light
for the
system to register the new time.
Although it may not be necessary to alter the filter cycle, it can be adjusted by
pressing the control buttons
warm
Mode
cool
Blower
Jet 1 Jet 2
Light
warm
Mode cool
Blower
Jet 1 Jet 2
Light
warm
Mode cool
Blower
Jet 1 Jet 2
Light
warm
Mode cool
Blower
Jet 1 Jet 2
Light
within three seconds.The display
message „SET START FiLTER 1“ (AM cycle, 0.00 -12.00 hrs) will appear. To set
the starting time of the filter cycle, press the
warm
Mode cool
Blower
Jet 1 Jet 2
Light
or
warm
Mode cool
Blower
Jet 1 Jet 2
Light
button. After pressing
warm
Mode cool
Blower
Jet 1 Jet 2
Light
the display message „SET STOP FiLTER 1“ will appear. now enter the stop
time using the
warm
Mode cool
Blower
Jet 1 Jet 2
Light
or
warm
Mode cool
Blower
Jet 1 Jet 2
Light
buttons as described above. After pressing the
warm
Mode cool
Blower
Jet 1 Jet 2
Light
button, the display message „SET STOP FiLTER 2“ (PM cycle, 12.00 - 24.00 hrs)
will appear.
When the
warm
Mode cool
Blower
Jet 1 Jet 2
Light
button is pressed, the whirlpool registers the new
cycle times and displays the current water temperature.
The first filter cycle is automatically activated at 8.00 hrs (8.00 AM).
Pump 1 works at low speed until 12.00 noon. The second filter cycle is automati-
cally activated at 18.00 hrs (6.00 PM). Pump 1 works at low speed until 22.00
hrs (10 PM). During the filtration period, the filtration pump and the ozone
generator are in operation. Before the filtration period starts the blower always
flushes the air channel system for 30 seconds.Pumps 1 and 2 are running for
1 minutes.
Switching valve
(position filter)
Cascade
on/off