background image

WWW.RSIWW.COM

38 of 48

Install Roof Vents

Make certain the pieces are in the correct positions before securing. 

Carefully follow the order of assembly to ensure an easy installation.

Wear proper safety gear including work shoes, gloves and goggles.

Unpack contents of Automatic Window Opener. Screw adjusting 

knob partially into threaded end of cylinder. Do NOT tighten. 

Fit piston rod connected to arm B into 

end of cylinder. Turn cylinder so holes 

next to adjusting knob are visible. 

Continue pushing cylinder onto piston rod until holes 

in end of cylinder line up with holes in arm A. Push 

arms apart if necessary. Secure with 

a threaded stud on each side.

Repeat steps 9.1A through 9.1D 

to prepare the second 

Automatic Window Opener.

Remove plastic film from both sides of V-4 

factory assembled vents. With side labeled 

“ Face inside” facing up, lay panel 

on flat clean surface. 

Measure and 

mark center 

of vent. 

Place opener with arm A on bottom 

inside vent, align with center mark.  

Mark screw placement. Using S-1  

screw, apply pressure to puncture the 

panel and predrill holes for next step.

Turn adjusting screw clockwise 

until arms are approximately 

6” apart.

9.1A       

9.1B       

9.1c       

9.1e

9.2A       

9.2B       

9.1D       

adjusting knob

cylinder

9.1B

piston rod

cylinder

arm B

arm A

QTY

Threaded Stud

4

QTY

Adjusting Knob

2

QTY

2

Cylinder

QTY

2

Handle

V-4

V-4

arm A

S-1

V-4

2

Factory Assembled Vent

QTY

24”

 

x

 

24

 

¾”

Center line for Arm A

Summary of Contents for MONT-12



















































Reviews: