Riverstone Networks MONT-12 Assembly Instructions Manual Download Page 41

Page: 41 / 50

WWW.RSIWW.COM

39 of 48

S-1

W-10

S-1

W-10

NOTE: VIEW FROM OUTSIDE.

Screw two S-1 screws through V-4 panel. Line up gripping channel on other side.

Continue to screw until secure. Do not over tighten as it may damage the vent.

Repeat steps 9.2A through

9.2C to prepare second vent.

From inside, hold Window Opener closed against vent. Slide vent at an angle through opening in

roof panels. Hook top lip of vent

onto curve in ridge

profile R-1.

Outside of vent rests on top of ledge on W-10 profile. Open vent to attach the other arm of

opener to top of inside W-10 profile. Position with arm overlapping trim so adjusting screw

can move freely. Screw two S-1 screws through panel and into gripping channel on other side to

secure. Do not over tighten as it may damage the vent.

From inside screw S-6 screw and spacer into the holes

on each end of the top of the vent. This will secure the vent to the greenhouse in windy conditions.

Repeat steps 9.3A through 9.3B to install second vent.

Repeat steps 9.4A to

secure second vent.

9.2c

9.2D

9.3A

9.3B

9.4A

9.3c

9.4B

NOTE: VIEWS FROM INSIDE.

NOTE: VIEWS FROM FRONT

NOTE: VIEWS FROM INSIDE.

gripping
channel

V-4

S-1

Gripping Channel

QTY

S-1

Connector

QTY

V-4

R-1

V-4

R-1

gripping
channel

V-4

W-10

Gripping Channel

QTY

S-1

Connector

QTY

V-4

W-10

R-1

S-6

V-4

S-6

S-6

Connector

QTY

NOTE: Make sure arm A overlaps aluminum trim on W-10

Summary of Contents for MONT-12



















































Search results

Summary of Contents for MONT-12

Reviews:

Related manuals for MONT-12

Brands by name

Popular brands

Riverstone Networks MONT-12, Assembly Instructions Manual

Search results

Summary of Contents for MONT-12

Reviews:

Related manuals for MONT-12

Brands by name

Popular brands