background image

8 Inspection and maintenance

EN

36

Rittal enclosure cooling unit

Fig. 56:

Unscrew and remove the corner brackets at the top 
and bottom

Half-way up, remove one spring clip from the front of 
the cooling unit on both the left and right.

Fig. 57:

Remove the spring clips

Hold the cooling unit as straight as possible when re-
moving it from the mounting cut-out.

Fig. 58:

Remove the cooling unit from the mounting cut-out

Set the device down safely in a suitable place.

Next, remove the device's cover as described in sec-
tion 8.4.3 "Removing the cover".

8.4.2

Removing an externally mounted unit

Where cooling units are externally mounted on the en-
closure, only the louvred grille must be removed initially 
prior to cleaning with compressed air. The rear panel in-
cluding all components can remain in the mounting cut-
out.

Remove the louvred grille as described in sec-
tion 5.3.5 "Internal mounting of the cooling unit".

Next, remove the device's cover as described in sec-
tion 8.4.3 "Removing the cover".

8.4.3

Removing the cover

Allow the unit to cool down for at least ten minutes be-
fore removing the cover. 
This should allow hot surfaces inside the unit to cool 
down sufficiently.

For SK 317880x and SK 317980x: Loosen the eight 
screws connecting the cover to the rear panel.

Note:
Please note that when removing the louvred 
grille, contrary to the illustrations shown in 
section 5.3.5 "Internal mounting of the cool-
ing unit",
 the cooling unit is fitted on an enclo-
sure door or side panel.

Caution!
After removing the cover, there is a risk 
of burn injuries from hot component sur-
faces inside the unit.

Caution!
The cooling unit is only stable while the 
hood and rear wall are joined together. It 
is therefore particularly important to se-
cure the rear panel to prevent it from fall-
ing before you remove the hood.

Summary of Contents for SK 3178800

























































Reviews:

Related manuals for SK 3178800