Rinnai RHFE-431WTA Service Manual Download Page 9

Page: 9 / 68

Rinnai Direct Vent Service Manual

Analog

Indicator

Light

Digital

LED

Name Definition Corrective

Action

64 68 72

High-limit

thermistor

disconnection

High limit thermistor
circuit is open.

Check the circuit. (troubleshooting)

68 72 76

High-limit

thermistor short

circuit

High limit thermistor
wire is trapped or
touching bare metal.

Check the circuit. (troubleshooting)

LO 60 64

Abnormal spark

sensed

•

Sparker is not off
within 20 seconds of
ignition.

•

1st spark is not
sensed within 2
seconds

•

2nd spark is not
continuous for 1
second after
solenoid valve
opens

Replace sparker

60 64 68

Abnormal

Combustion Fan

RPM

RPM is not achieved
within a certain time or
exceeds the RPM
limit.

Check for obstacle preventing fan from turning
freely.
Check wiring harness to motor for damage or
loose connections.

64 68

ON/OFF Switch

Failure

The ON/OFF switch
connects continuously
for more than 15
seconds.

Check the circuit. (troubleshooting)
Replace switch.

LO 60

Solenoid Valve

Failure

For either solenoid
valve, SV1 or SV2, the
signal and response
signal are different.

Check the circuit. (troubleshooting)
Replace gas valve.

80 72

Flame

Rod

Failure

Flame rod output does
not cease within 20
seconds

Check the circuit. (troubleshooting)
Replace flame rod.

72 76 80

73 Communication

Failure

Data transfer between
CPU and E2PROM
fails.

Disconnect the power and re-apply power.

Pressure Sensor No signal from the

pressure sensor.

Check the circuit. (troubleshooting)

Flue Block

The pressure sensor
signal is below its limit.

Check the flue and termination for proper
installation and blockage.

60 64 68

72 76

Flue Block

Flue blockage has
been detected based
on fan speed.

Check the flue and termination for proper
installation and blockage.

Fault Isolation Codes

Summary of Contents for RHFE-431WTA





































































Search results

Summary of Contents for RHFE-431WTA

Reviews:

Related manuals for RHFE-431WTA

Brands by name

Popular brands

Rinnai RHFE-431WTA, Service Manual

Search results

Summary of Contents for RHFE-431WTA

Reviews:

Related manuals for RHFE-431WTA

Brands by name

Popular brands