background image

Rinnai 22 

EHPA Heat Pump OIM

OPERATION SEQUENCE OF CONTROLLER 

When  the  power  supply  turns  on,  the  heat  pump  control  system  initiates  and  will  check  the  unit’s  operating 

parameters. The controller will check on all sensors, pressure switches and also main voltage.  If conditions are 

suitable (i.e All  reading within the reasonable range) and there is enough energy available in the surrounding air, 

the fan, circulating pump and compressor will turn on. If not enough energy is detected in ambient air then the 

controller calls for the booster heating element to run.  
There will be a delay of approximately 2 minutes from the time the main power is switched on before the pump, fan 

and compressor begin operating.
The unit is self regulating so there are no internal adjustments to be made during commissioning. When the unit is 

operated for the first time, it runs through an initial heat up cycle, allow time for the initial heat up cycle. Depending 

on the ambient conditions this can take several hours. 

Once its first heat up cycle is complete, empty approximately 60 litres of hot water from the tank through the PTR 

valve outlet then allow the water in the tank to re-heat. Once the re-heat cycle is completed measure the water 

temperature at the PTR outlet again. The temperature will be approximately 60º C.

If for any reason the unit does not start, the water is cold and the controller unit is not displaying any LED lights, an 

electrician should test that power is available to the heat pump.

1

2

3

4

5

6

7

8

9

10

11

12

1

DIP Switch Test & Configuration

7

Low Pressure Switch

2

Ambient Temperature Sensor

8

High Pressure Switch

3

Water Tank Temperature Sensor

9

Programming Port

4

Compressor Discharge Temperature Sensor

10 Compressor, Element , Main Power

5

Fan Coil (Evaporator) Temperature Sensor

11 2 A Fuse

6

LED Lights

12 Fan, Pump, Defrost

INSTALLATION

Summary of Contents for Enviroflo EHPA250VM

























Reviews: