background image

Rinnai 

RDV 600_700ER OM

WARNING

MODIFICATIONS.

DO NOT MODIFY THIS APPLIANCE

.

Modifying  from  original  specifications  may  create  a  dangerous  situation  and  will  void  your 

warranty. Failure to comply with these instructions could result in a fire or explosion, which could 

cause serious injury, death or property damage.

DO NOT 

modify the electrical wiring of this appliance.

If the power cord is damaged or deteriorated it 

MUST

 be replaced by an authorised person. 

Failure to do so may result in electric shock, fire, serious injury or product failure.
Improper installation, adjustments, service or maintenance can cause serious injury, death or 

property damage. Such work 

MUST ONLY

 be performed by an authorised person.

WARNING

GENERAL SAFETY WARNINGS

This appliance is 

HEAVY

, during installation the use of a mechanical lifting aid is recommended, 

noting that improper lifting may result in serious injury.

WARNING

: This heater 

MUST

 

NOT

 be used if any of the glass panels are damaged.

Flue terminal 

MUST

 always vent directly to outdoors. 

DO NOT

 extend the flue vertically or 

horizontally  in  ways  other  than  prescribed  in  this  appliance  manufacturer’s  installation 

instructions. 

ONLY

 the flue components specified by Rinnai 

MUST 

be used. 

When considering installation ensure minimum 

clearances as follows are adhered to, refer Fig. 1.

Heat radiating from the front of this heater 

may  over  time  affect  the  appearance  of  some 

materials used for flooring such as carpet, vinyl, 

cork or timber. This effect may be amplified if the 

air in the room contains cooking vapours, candle 

vapours and cigarette smoke, etc. To avoid this 

possibility,  it  is  recommended  that  a  mat  or 

similar protective sheet be placed in front of the 

appliance, extending at least 750 mm in front of 

the dress guard. Refer to the installation manual 

for mantle clearances, additional installation 

information and warnings.
This appliance 

MUST

 

NOT

 be installed where 

curtains  or  other  combustible  materials  could 

come into contact with it. In some cases curtains 

may need restraining.
This appliance is 

NOT

  intended  for  use  by 

persons  (including  children)  with  reduced  physical,  sensory  or  mental  capabilities  or  lack  of 

experience and knowledge, unless they have been given supervision or instruction concerning 

use of the appliance by a person responsible for their safety.

The appliance is 

NOT

 intended for use by young children or infirm persons without supervision. 

Young children and the infirm 

SHOULD

 be supervised at all times when in the vicinity of this 

heater while it is in operation.
The heater 

MUST

 

NOT

 be located immediately below a power socket outlet.

A dedicated 230 V earthed 10 Amp power point must be used with this appliance.
Refer to local gas authority for confirmation of the gas type if you are in doubt.
Suitable 

ONLY

 for indoor installation.

DO NOT

 operate this appliance before leak checking hoses and gas cylinder connection.

This heater 

MUST

 

NOT

 be used if either of the glass panels are damaged.

NOT

 to be connected to an LP gas cylinder located indoors.

Please keep this instruction booklet in a safe place for future reference. All dimensions referred 

to in these instructions are in millimetres, unless otherwise specified. 

750mm

1000m

m

150mm*

150mm*

**400m

m

*150mm is the minimum clearance from 

edge of glass to combustibles.

**400mm is the minimum top clearance from 

edge of glass to underside of mantel shelf.

WARNINGS & IMPORTANT INFORMATION

Summary of Contents for 650





















Reviews: