background image

1

INTRODUCTION

General layout (fig. 1)

Water pressure sensor /trasducer

2   Drain valve

Three port valve actuator

DHW heat exchanger

5   Pump 

Bottom auto air vent (AAV)

Pressure gauge

Condense trap

Return sensor 

10  Fumes sensor
11  Flue gas analysis test point
12  Flue outlet & air intake 
13  Ignition transformer
14  Limit thermostat
15  Flow temperature sensor
16  Top AAV
17  Sensing electrode
18  Spark electrode
19  Cylindric Burner 
20  Condensate level sensor
21  Main heat exchanger
22  Fan assembly
23  Degassing hose
24  Mixer
25  Expansion vessel 
26  DHW temperature sensor
27  Gas valve 
28  Flow meter

R   Heating return connection 

Heating flow connection

Gas connection

Hot water outlet

Cold water inlet

All  installers  are  asked  to  follow  the  Benchmark  Scheme  by  ad-

hering to the Code of Practise, which can be obtained from www.

centralheating.co.uk.

There are no banned substances used in the manufacture of 

these appliances.

The 

Linea ONE

 is a high-efficiency combination boiler with inputs 

to heating 30 kW & DHW of 38 kW. Each appliance – by design – 

incorporates electronic ignition, circulating pump, expansion vessel, 

safety valve, water pressure sensor and automatic by-pass.

The 

Linea ONE

  is  produced  as  room  sealed,  category  II2H3P 

appliances, suitable for internal wall mounting applications only. It 

is provided with a fan powered flue outlet with an annular co-axial 

combustion air intake that can be rotated – horizontally – through 

360 degrees for various horizontal or vertical applications.  The Linea 

ONE can also be used with the Vokera twin flue system.

The

 Linea ONE

 is approved for use with B23P-B53P-C13-C13x- 

C23-C33-C33x-C43-C43x-C53-C53x-C63-C63x-C83-C83x-C93-

C93x type flue applications.

These appliances are designed for use with a sealed system only; 

consequently they are not intended for use on open vented systems 

nor are they intended for external applications.
When the product reaches the end of its life it should not be dispo-

sed of as solid urban waste but should be brought to a separated 

waste collection facility

Linea ONE

 boiler complies with basic requirements of the following 

Directives: Gas directive 2009/142/EC; Yield directive 92/42/EEC; 

Electromagnetic compatibility directive 2014/30/EU; 

Low-voltage directive 2014/35/EU;  

Directive 2009/125/EC Ecodesign for energy-using appliances; 

Directive 2010/30/EU Indication by labelling of the consumption of 

energy by energy-related products; 

Delegated Regulation (EU) No. 811/2013; 

Delegated Regulation (EU) No. 813/2013; 

Delegated Regulation (EU) No. 814/2013. 

Fig. 1

INSTALLATION AND SERVICING INSTRUCTIONS

MAIN FEATURES

-  Fully automatic modulating circulation pump
-  High performances in DHW mode, 3 stars according EN 13203-1 

(flow meter and larger DHW heat exchanger) 

-  Combustion Range Rated, output adjustable according the de-

signed  home energy requirement

-  Premix fully condensing combustion

R

F

I

O

G

Summary of Contents for Vokera Linea ONE









































Reviews: