A.O. Smith Burkay HW-300 Instruction Manual Download

Page: 1 / 62

GAS FIRED COMMERCIAL COPPER BOILERS

Instruction Manual

PRINTED 0213

321078-002

Thank you for buying this energy efficient boiler.

We appreciate your confidence in our products.

MODELS: HW

300, 399, 420, 520, 670

FOR HYDRONIC HEATING AND

HOT WATER SUPPLY

UP - FLOW MODELS

INSTALLATION - OPERATION

MAINTENANCE - LIMITED WARRANTY

INDOOR ONLY

25589, Highway 1

McBee, SC 29101

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.
Do not touch any electrical switch; do

not use any phone in your building.
Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.
If you cannot reach your gas supplier,

call the fire department.

Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

•
•

•

Summary of Contents for Burkay HW-300































































Search results

Summary of Contents for Burkay HW-300

Reviews:

Related manuals for Burkay HW-300

Brands by name

Popular brands

A.O. Smith Burkay HW-300, Instruction Manual

Search results

Summary of Contents for Burkay HW-300

Reviews:

Related manuals for Burkay HW-300

Brands by name

Popular brands