Riello RX 150 S/PV, Installation, Use And Maintenance Instructions

Page: 43 / 56

41 20151674 GB
List of parameters PME71.901...)
The following pages have the Menus and the list of parameters
for setting up the LCD AZL 2 ... Display for the LME 71 ... control
box with PME 71.901 ...
The values shown in the "Factory setting" column in the table be-
low, are indicative (Control box not programmed).
A List of parameters PME71.901...)
WARNING
To display/change the parameters it is neces-
sary to use the AZL 21 ... display kit (page 44)
accessing with the password.
Parameter
Modification
Value range
Resolution
Factory Set-
ting
Password
reading
level to
level
Password
writing level
to level
No. Description Min. Max.
000 Internal parameter
41 Password for heating engineering (4 characters) Modification xxxx xxxx --- --- --- OEM
42 Password OEM (5 characters) Modification xxxxx xxxxx --- --- --- OEM
60 Backup/restore Modification Restore Backup --- --- --- SO
100 General notes
102 Identification date Reading only --- --- --- --- mode ---
103 Identification number Reading only 0 9999 1 0 mode ---
113 Burner identification Modification x xxxxxxxx 1 burnErId mode SO
123 Step control min output. Modification 1% 10% 0.1 2 SO SO
140
Displaying the unit operation mode and display-
ing AZL2...
1 = standard (program phase)
2 = flame 1 (QRA.../ION)
3 = flame 2 (QRB.../QRC...) ® not used
4 = output active (output value)
Modification 1 4 1 4 SO SO
164 Number of resettable start-ups Resettable 0 999999 1 0 mode mode
166 Total number of start-ups Reading only 0 999999 1 0 mode ---
170.00 Switching cycles relay contact K12 Reading only 0 999999 1 0 mode ---
170.01 Switching cycles relay contact K11 Reading only 0 999999 1 0 mode ---
170.02 Switching cycles relay contact K2 Reading only 0 999999 1 0 mode ---
170.03 Switching cycles relay contact K1 Reading only 0 999999 1 0 mode ---
171 Max. relay commutation cycles Reading only 0 999999 1 0 mode ---
200 Burner Control
224 Air pressure switch special time Modification 0s 13.818 s 0.294 s 13.818 s SO OEM
225 Pre-purging time - 2.1 seconds Modification 0s 1237 s 4.851 s 29.106 s SO OEM
226 Spark pre-ignition time Modification 1.029 s 37.485 s 0.147 s 6.174 s SO OEM
230
Interval: End of the safety time - resetting of the
load regulator
Modification 3.234 s 74.97 s 0.294 s 9.408 s SO OEM
234 Post-purging time Modification 0s 1237 s 4.851 s 19.404 s SO OEM
235
Air pressure switch input
0 = inactive
1 = active
Modification 0 1 1 0 SO OEM
240.00
Repetitions meter
Limit value of flame loss during operation
Modification 0 2 1 0 SO OEM
240.01
Repetitions meter
Limit value of No flame at the end of the safety
time
Modification 0 1 1 1 SO OEM
241.00
Valves Seal Control
0 = OFF
1 = ON
Modification 0 1 1 1 SO OEM
241.01
Valves Seal Control
0 = during pre-purging
1 = during post-purging
Modification 0 1 1 1 SO OEM
241.02
Valves Seal Control
0 = according to P241.01
1 = during pre-purging and post-purging
Modification 0 1 1 0 SO OEM
242 Evacuation of valve seal control test area Modification 0s 2.648 s 0.147 s 2.648 s SO OEM
243
Atmospheric pressure valve seal control time
test
Modification 1.029 s 37.485 s 0.147 s 10.290 s SO OEM
244 Filling the valve seal control test area Modification 0s 2.648 s 0.147 s 2.648 s SO OEM
245 Gas pressure valve seal control time test Modification 1.029 s 37.485 s 0.147 s 10.290 s SO OEM