background image

TECHNICAL ASSISTANCE SERVICE

44

CONVERSION FROM ONE GAS TYPE TO ANOTHER

The boiler can be converted from one gas type to another 
quite simply, without even having to remove the burner. 
The burner comes configured for use with methane gas 
(G20) as stated on the boiler’s gas plate.
The burner can be converted for use with propane gas 
(G31) using the kit supplied with the boiler. Proceed as 
follows to perform the conversion.

 

- Disconnect the electricity supply from the boiler and 

shut off the gas cock. 

 

- Remove the top front panel. 

 

- Release the control panel and tilt it forwards.

 

- Unscrew the nut (A). Move the pipe (B) gently to one 

side and replace the diaphragm inside the pipe with the 
new diaphragm supplied in the kit. 

 

- Reverse the above steps to reassemble the boiler. 

 

- Switch the electricity supply to the boiler back on and 

open the gas cock.

Adjust the boiler as instructed in the “SETTINGS” section, 
taking care to use the values for LPG. 

Labels

 

- Remove the G20 label from the outside of the boiler 

casing. 

 

- Apply the G31 label to the inside of the casing, covering 

the old G20 label. 

 

b

Gas conversions must only be carried out by quali-
fied personnel.

 

b

Apply the new gas label supplied in the kit on com-
pletion of the conversion.

°C

0

120

20

100

40

80

60

A

B

Country of destination:

Type of boiler:

Boiler category: 

II2H3P

Gas supply pressures: 

G20

G31

20 mbar

37 mbar

Manufacturer setting:

G20 - 20 mbar

IMPORTANT!

Read the instruction manual thoroughly 

before installing and starting up the boiler.

B23P, B53P, C13, C33, C43,

C63, C83, C13x, C33x,

C43x, C53x, C63x, C83x

GB

CALDAIA REGOLATA PER: CHAUDIERE REGLEE POUR:

KESSEL GEREGELT  FÜR

PAESE DI DESTINAZIONE:

PAYS DE DESTINATION:

BESTIMMUNGSLAND :

T067745I2

G31 - 37mbar

IT

Summary of Contents for 20044965





















































Reviews: