background image

 

- ACTIVE series - 

 

- 28 -

 

S3M

 

-

 

S

INGLE PHASE VERSION

 

 

The first wire to be connected is the protective earth wire, which is to be inserted in the terminal marked PE. 
During operation the UPS must be connected to the earthing system.  

 
Connect the input and output cables to the terminal blocks as indicated in the figure below: 
 

TERMINAL BLOCK COLOURS 

RED 

BLACK 

GREY 

BEIGE 

BLUE 

External battery positive 

External battery negative 

Input & Bypass Phases 

Output Phases 

Input, Output and external 

battery Neutral 

 

 

THE INPUT AND BYPASS NEUTRALS MUST ALWAYS BE CONNECTED. 

 
 

 

 

Jumpers (for more details about their installation or removal, refer to "APPENDIX")

 

 
To connect a single-phase source to the input: fit the supplied jumper to link the three input terminal blocks, as shown in the image 
above. The jumper is supplied within the accessories box. Then connect the phase cable to the L1 terminal block. 

 
 
 

D

UAL 

I

NPUT VERSION

 

 

 

THE INPUT AND BYPASS LINES MUST BE REFERENCED TO THE SAME NEUTRAL POTENTIAL. 

 
 

 

 
 

Note:

 connection to the BATTERY terminal blocks is only required if an 

(optional) 

Battery Cabinet is present. 

 

 

Jumpers: 

For more information regarding all possible configurations, refer to 

Table 23

.

 

 

Summary of Contents for Sentryum S3M













































Reviews: