background image

Operating Instructions and Parts Manual

6

ELECTRICAL

  Risk of electrical shock. This pump is designed 

for indoor installation unless housed and protected from the elements.

  Risque de choc électrique! Cette pompe est 

conçue pour une utilisation à l'intérieur, sauf si elle est à l'abri et 

protégée contre les intempéries.

• 

This installation must be in accordance with the National Electric 

Code and all applicable local codes and ordinances.

• 

The voltage of power supply must match the voltage of the 

pump. The motors can be converted to 115 or 230 volts by 

changing the voltage selector to the desired voltage. Remove 

rear cover of motor by unscrewing both screws to expose voltage 

selector. Rotate dial so desired voltage is completely visible within 

notch (Figure 4).

• 

If wire run is a short distance, a cord/plug assembly may be 

used as long as it meets the minimum wire gage size, called out in 

Chart 3, above. Time delay fuses are recommended over standard 

fuses for motor circuit protection. All pump motors have built-in 

automatic overload protection that will prevent damage to the 

motor due to overheating.

• 

Do NOT connect to electric power supply until unit is 

permanently grounded. Connect ground wire to approved ground 

then connect terminal provided.

• 

A metal underground water pipe or well casing at least 10 feet 

long makes the best ground electrode. If plastic pipe or insulated 
fittings are used, run a wire directly to the metal well casing or use a 

ground electrode furnished by the power company.

• 

There is only one proper ground terminal on the unit. The 

terminal(s) is located under the pressure switch cover, is painted 

green and is identified as GRD. The ground connection must be 

made at this terminal (Figure 5). The ground conductor must not be 

smaller than the circuit conductors supplying the motor.

  Disconnect power and release all pressure from 

the system before attempting to install, service, relocate or perform any 

maintenance.

  Débrancher de la source d’alimentation puis 

dissiper toute la pression du système avant d’essayer d’installer, de 

réparer, de déplacer ou de procéder à l’entretien.

L2 3

L1

1

Figure 5 - Electrical Connections

MOTOR

LINE

GROUND SCREW

OPERATION

PRIMING THE SHALLOW WELL PUMP

  To prevent damage to the pump, do NOT start 

motor until pump has been filled with water.

  Pour éviter d'endommager la pompe, ne pas 

démarrer le moteur tant que la pompe n'a pas été remplie d'eau.

1.   Remove prime plug (Figure 3).
2.   Fill pump and piping completely full of water.
3.   Replace the prime plug.
4.   Open a faucet to vent the system.
5.   Start the motor. Water will pump in a few minutes. If pump fails 

to prime in 5 minutes, stop motor and refill pump with water. 

Priming time is proportional to the amount of air in inlet pipe.

6.   Let the system operate for several minutes to flush all pipes.
7.   Close faucet and allow pump to build pressure in tank. When 

the pressure reaches the cut-out setting, the motor will stop.

The system is now in operation and will automatically cycle on 

demand.

Figure 4 - Voltage Selector

Summary of Contents for RSWS Series













Reviews: