background image

9

WARNING:

Do  not  allow  familiarity  with  tools  to  make  you 
careless. Remember that a careless fraction of a 
second is sufficient to inflict severe injury.

WARNING:

Always wear safety goggles or safety glasses with 
side shields when operating tools. Failure to do so 
could result in objects being thrown into your eyes 
resulting in possible serious injury.

WARNING:

Do  not  use  any  attachments  or  accessories  not 
recommended  by  the  manufacturer  of  this  tool. 
The use of attachments or accessories not recom-
mended can result in serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

  Hammer drilling in concrete, brick, or other masonry

 

Drilling in wood

 

Drilling in ceramics, plastics, fiberglass, and laminates

 

Drilling in metals

 

 Driving screws

 

Mixing paint

OPERATION

This  product  will  accept  RIDGID  8  V  lithium-ion  battery 
packs and RIDGID 8 V nickel-cadmium battery packs.
For complete charging instructions, refer to the Operator’s 
Manual  for  the  battery  packs  and  chargers  listed  in  the 
General Safety Rules.

BATTERY PROTECTION FEATURES

RIDGID 8 V lithium-ion batteries are designed with features 
that protect the lithium-ion cells and maximize battery life. 
Under  some  operating  conditions,  these  built-in  features 
may  cause  the  battery  and  the  tool  it  is  powering  to  act  
differently from nickel-cadmium batteries.
During some applications, the battery electronics may signal 
the battery to shut down, and cause the tool to stop running. 
To reset the battery and tool, release the trigger and resume 
normal operation.
NOTE: To prevent further shut down of the battery, avoid 
forcing the tool. Switching to a lower speed will also prevent 
shut down.
If releasing the trigger does not reset the battery and tool, 
the battery pack is depleted. If depleted, the battery pack will 
begin charging when placed on the lithium-ion charger. 

Summary of Contents for R840011



















Reviews: